Remodelers NearbyFrom the state registers

How should a tiled shower or tub surround be waterproofed?

Tile and grout are a wearing surface. Water gets past them. The wall behind needs a backer that survives being wet, such as cement board, plus either a waterproofing coat on its face or a drainage layer behind it. Paper-faced drywall, the green kind included, does not belong behind a tiled tub or shower.

Remodelers Nearby editorial desk. Checked against the sources listed at the foot of the page in November 2026.

A failing shower can look fine for years. The tile is straight, the grout is clean, and behind it the wall is slowly turning to paste. By the time a tile comes loose or a stain appears on the ceiling below, the repair is a tear-out. All of the protection in a shower is in layers you will never see again once the tile is on, which is why this is the part of a bathroom remodel worth standing over.

What the backer has to do

The US Department of Energy's Building America program publishes installation guidance for this exact assembly. Its instruction is to install cement board or an equivalent moisture-resistant backing on walls behind tub and shower enclosures that are finished in tile or in panels with caulked joints (Building America Solution Center). The same guide sorts the common boards this way:

BackerBehind a tiled tub or showerNote
Cement boardAcceptableWater resistant, not waterproof, unless made as a waterproof board
Fiber-cement backerAcceptableTreated as equivalent to cement board
Coated glass-mat gypsum backerAcceptableGypsum core with glass fiber facings in place of paper
Paper-faced gypsum boardNot acceptableDoes not stop moisture getting through
Moisture-resistant "green board"Advised againstStill a paper-faced gypsum product

There is one exception in the guide. Behind a one-piece fiberglass unit with no joints, paper-faced board can be acceptable if it meets the ASTM mold-resistance standards, because no water reaches it. The moment the surround has grout lines or caulked panel joints, that exception is gone.

Cement board alone is not waterproofing

This is the point that gets lost. Cement board does not rot, but water passes through it. The Building America guide is blunt: you must coat it with a fluid-applied waterproofing, edges included, or put a water-resistant barrier behind it that drains. A wall with bare cement board screwed to the studs and tile set straight on it is an incomplete assembly, however solid it feels.

So there are two sound ways to build the wall. The surface method puts a continuous membrane on the face of the board, rolled or troweled on, and the tile bonds to that. The drainage method hangs a barrier on the studs behind the board and laps it over the tub flange or into the pan so that whatever gets through runs down and out. Either works. What does not work is half of each, or a membrane that stops short of the corners, the niche and the valve opening. Those three places are where leaks tend to start.

Exterior walls need one more step

When the tub or shower sits on an outside wall, the cavity behind it is closed off for good the day the backer goes on. The guide calls for sealing pipe and wire penetrations and insulating the stud bays before the board is installed. Miss it and you have built a cold, uninsulated box behind the wettest wall in the house.

The floor of the shower

A tiled shower floor follows the same logic with higher stakes, because water sits on it. The waterproof layer has to slope to the drain, turn up the walls and over the curb, and tie into the wall waterproofing with the upper layer lapped over the lower one. Ask your contractor two questions before tile: how the pan was sloped beneath the membrane, and whether it was plugged and filled with water overnight to prove it holds. A contractor who waterproofs carefully will have photos and will not mind the question.

What to look at before the tile goes on

Permits for bathroom work in Oregon

Retiling does not need a permit on its own account. The Oregon Building Codes Division lists resurfacing shower walls, regrouting tile and replacing a toilet, sink or exposed faucet as plumbing work that needs no permit, and tile is on the building permit exemption list. The permit arrives with the work behind the wall: altering piping inside walls or under floors needs a plumbing permit, a new or relocated bath fan needs a mechanical permit, and new wiring needs an electrical one.

Adding a bathroom where there was none is a different job. Portland, for one, requires plumbing and building permits for an added bathroom and notes that electrical or mechanical permits may be needed as well (Portland Permitting and Development).

Which means a shower rebuilt in place, with the valve and drain where they were, can legally go from studs to tile without an inspector ever seeing the waterproofing. Nobody is checking that layer but you.

Questions clients ask

Is green board acceptable behind shower tile?

Not according to the Building America installation guide, which says moisture-resistant gypsum and green board products should not be used behind tub and shower surrounds. Use cement board, fiber-cement or a coated glass-mat backer, with waterproofing.

Does cement board need a waterproof membrane?

Yes, unless the board is sold as waterproof. Standard cement board resists water damage but lets water through, so it needs a fluid-applied coating on its face and edges or a draining barrier behind it.

Do I need a permit to retile a shower in Oregon?

Resurfacing shower walls and regrouting tile are on the state's list of work that needs no plumbing permit. Moving the valve or drain, altering piping inside the wall or adding a fan brings in plumbing or mechanical permits.

Sources

Keep reading

Looking for a contractor? Browse the Oregon and Washington register lists.